Hooking up mackie 402 to mac for editing

#HOOKING UP MACKIE 402 TO MAC FOR EDITING HOW TO#
#HOOKING UP MACKIE 402 TO MAC FOR EDITING MANUAL#

Either one can be used to feed a mono stage monitor. Each of the stereo inputs will be sent to both mixer outputs. Set the Mackie 402 pan switch to 'out' (mono sum). Use a a pair of splitter 'Y' cables if you need them to feed both the (2) summing mixer inputs and teh house PA. and connect your main stereo outputs to the channel-1 and channel-2 inputs. Otherwise pick-up a small mixer like a Mackie 402 VLZ. Some stage monitors actually have a stereo summing input (look for a monitor with a pair of red and white RCA jacks). Every audience member will hear a slightly different mix. What the audience hears will be determined by their positioning relative to the (2 or more) PA speakers, and the room acoustics.

Even then it won't be equal to what all members of the audience are hearing if you're using a stereo mic input mix. You will still have to sum the two stereo outputs. Stereo out but only connecting to one monitor.Д¬orrect, there is no advantage of setting up a parallel stereo mix on the group buses.

#HOOKING UP MACKIE 402 TO MAC FOR EDITING MANUAL#

Please see your MG124CX Owner's Manual pp.11 (partial clip attached below).Д¬ould I send all the channels to the group 1/2 bus besides the ST bus, but then the same problem would exist. Obviously, keep the mics away from the stage monitor. Who ever suggested panning to a 'AUX left' doesn't understand basic mixer architecture.Д«e careful to not set your stage monitor level too high to avoid possible feedback. Just connect a single TRS/TRS cable from the AUX out to your powered stage monitor and balance the stage mix for each channel using the channel strip AUX send pots.ДЄUX outs are virtually always mono outputs and are unaffected by panning. The AUX send is before the pan pot and is simply a sum of all channels which have the AUX control turned up. The AUX output is not a Left or right stereo output. The 'Effects' send is effectively a second AUX out but is intended for use with an outboard effects processor, or an 'effects' chain since it includes a remote bypass function. Your mixer (I'm assuming it's really a MG124CX, not a 'MG1224CX') has one (labeled) mono AUX send out.

The exception (a real 'no-no') is using a 'Y' XLR splitter to connect a single powered mic to (2) phantom powered mic inputs. Parallel 'Y' splitters can safely be used to connect one output to (2) inputs, but never to connect (2) outputs to one input. Who ever suggested doing that has no competency in audio engineering. It's very bad engineering practice and potentially can cause damage. The two mains could be connected to two inputs on a small summing mixer to provide one mono output, but should never be connected to each other with a 'Y' cable.

Outputs should never be directly connected together. The audio forum where every answer is worth exactly what you pay for it.Дo not use 'solution' No.

Get a TRS Y cable and plug in LEFT and RIGHT monitor output from the board and send it down the single cable to the monitor. I could pan all the channels left, then just plug the monitor into AUX left and send it down single cable to the monitor (although wouldn't that also pan left the mains mix.)Дў. I have been told 2 things and I am not sure which is the better answer:ДЎ.

#HOOKING UP MACKIE 402 TO MAC FOR EDITING HOW TO#

I understand the mixer AUX monitor settings, but I am getting confused on how to get signal out of the mixer that has LEFT and RIGHT TRS jacks when I am going out to a single stage monitor (TRS). Lately we have had a need to use a stage monitor to better hear ourselves. Generally we just plug the mains into the house system and all is well. We have a Yahama MG1224CX mixer we take on the road. We are a 6 person A Capella group that sings outside, so a mixer is important for us for balance purposes.

Hooking up mackie 402 to mac for editing